1、給料口應避開滾筒或托輥的正上方；
1. The feeding port shall avoid directly above the drum or idler;
2、為減輕物料對膠帶的沖擊與磨損，給料方向應順膠帶的運行方向；
2. In order to reduce the impact and wear of materials on the belt, the feeding direction shall be along the running direction of the belt;
3、物料下落到膠帶上的落差應盡量減??；
3. The drop of materials falling on the tape shall be minimized;
4、膠帶受料段應縮短托輥間距和采取緩沖措施。為防止刮破膠帶，擋料裝置刮板清掃裝置和卸料裝置與膠帶的接觸部分應采用硬度適宜的橡膠板，不要采用夾有布層的膠帶頭；人字型橡膠輸送帶
4. The distance between idlers shall be shortened and buffer measures shall be taken in the material receiving section of the belt. In order to prevent the tape from being scratched, the rubber plate with appropriate hardness shall be used for the contact part between the material retaining device, scraper cleaning device and unloading device and the tape, and the tape head with cloth layer shall not be used; Herringbone rubber conveyor belt
5、每天檢查托輥滾筒，發現不能正常運轉的及時更換，再有檢查托輥滾筒上面是否有附著物，及時清理。
5. Check the idler drum every day. If it is found that it cannot operate normally, replace it in time. Then check whether there are attachments on the idler drum and clean it in time.

6.  所有的輸送帶必須接成環形才能使用，也就是環形輸送帶，所以輸送帶接頭的好壞直接影響輸送帶的使用壽命和輸送線能否平穩順暢地運行。一般輸送帶接頭常用方法有機械接頭、冷粘接接頭、熱硫化接頭等。橡膠輸送帶
6. All conveyor belts must be connected into a ring before they can be used, that is, the ring conveyor belt. Therefore, the quality of the conveyor belt joint directly affects the service life of the conveyor belt and whether the conveyor line can run smoothly. The common methods of conveyor belt joint include mechanical joint, cold bonding joint, hot vulcanization joint, etc. Rubber conveyor belt
7.橡膠輸送帶運行速度不應大于5.0米/秒，運輸塊度大，磨損性大的物料和使用固定犁型卸料裝置時應盡量采用低速。當橡膠輸送帶的運輸速度超過這個速度機會影響輸送帶的使用壽命。所以建議使用的時候，要保證運輸速度不應該超過5.0米/秒。
7. The running speed of rubber conveyor belt shall not be greater than 5.0m/s. Low speed shall be used as far as possible when transporting materials with large lumpiness and high wear and when using fixed plow unloading device. When the transportation speed of the rubber conveyor belt exceeds this speed, it will affect the service life of the conveyor belt. Therefore, it is recommended to ensure that the transportation speed should not exceed 5.0 M / s.
以上就是今天給大家講解的詳細內容，更多的精彩內容請點擊我們的網站山東輸送帶皮帶http://ujkdbkh.cn，我們會有更多的精彩內容等您查看.
The above is the detailed content explained to you today. For more wonderful content, please click our website Shandong conveyor belt http://ujkdbkh.cn , we will have more wonderful content for you to see